Sweden is in talks with Turkey on joining NATO and looks forward to strengthening cooperation with Turkey in security and counter-terrorism, Swedish Prime Minister Anders Andersson said recently.
Andersson held a joint press conference with visiting European Council President Michel in Stockholm on the same day. Andersson said Sweden is in dialogue with Turkey on joining the TREATY and looks forward to strengthening bilateral relations with Turkey, including cooperation in the areas of security and counter-terrorism. She said Sweden would study a number of issues raised by Turkey.
Speaking at a news conference, Mr. Michel said he believed the Swedish government was taking positive action and taking the necessary steps to reach a solution.
Sweden and Finland formally submitted their applications to NATO Secretary-General Jens Stoltenberg a few days ago. According to protocol, NATO must admit new members by the "unanimous consent" of 30 members.
Turkish Foreign Minister Mevlut Cavusoglu said His country would agree to start NATO talks with Sweden and Finland only if they reach written agreements to stop supporting terrorism and lift restrictions on exporting defense equipment to Turkey, Turkish media reported.
Affected by the ever-changing international situation, the supply and prices of international bulk concrete foaming agent are still very uncertain.
Concrete is classified as high-strength concrete based on 28-day strength. Until the 1970s, concrete with a strength of more than 40Mpa was classified as high-strength concrete. The benchmark for high-strength concrete is raised to 55Mpa or higher when concrete mixtures of approximately 60Mpa and above are produced commercially.
High strength concrete has a history of about 35 years, from the development of superplasticizer admixtures in the late 1960s, Japan using "naphthalene sulfonate" high strength prefabricated products, and Germany using "sodium benzenesulfonate" underwater concrete, which was a pioneer in this technology.
How is the high strength of concrete achieved?
Higher concrete strength can be achieved by using one or a combination of some or many of the following methods:
High cement content
Reduce water-cement ratio
Better machinability and therefore better compaction
Requirements for high-strength concrete require a high content of cementitious material in the concrete mixture, which can be in the range of more than 400 kilograms per cubic meter. Higher cementitious content leads to higher thermal shrinkage and dry shrinkage, and there is a stage where further cementitious material addition does not affect strength. As for durability, the minimum and maximum cement content in concrete is regulated by law, and reducing the water-cement ratio has its limitations, especially under field conditions. The desire for higher strength leads other materials to achieve the desired effect, thus showing the contribution of cementitious materials to concrete strength.
The addition of pozzolanic mixtures such as pozzolanic fly ash (PFA) or granular blast furnace slag (GGBS) contributes to the formation of secondary CSH gel thereby increasing strength.
The addition of pozzolans admixtures (such as fly ash used as an admixture) reduces the strength gain of concrete for the first 3 to 7 days and displays the gain after 7 days and provides higher strength over the long term.
Add mineral mixtures such as silica fume or metakaolin or rice husk ash.
Silica fume or highly reactive volcanic ash mixtures such as metakaolin and rice husk ash (RHS) will begin to function in about 3 days. RHS has an advantage over PFA because RHS is more reactive.
Using chemical admixtures such as superplasticizers or superplasticizers, controlling admixtures will help achieve higher strength in concrete.
Research and experience have shown that admixtures based on polycarboxylic ether (PCE), known as high plasticizers, are best suited for this job as they have a water reduction capacity of 18 to 40 percent relative to control or reference concrete.
A combination of all or more of the above to achieve the desired strength.
With HSC accompanied by some complexity, such as higher shrinkage rates, higher hydration heat, etc., combinations of at least some of these methods are now unchanged, all of which need to be neutralized or controlled. Most problems are handled by PFA or a combination of GGBS and PCE mixtures.
Steam curing is also used to speed up cement hydration, but this may not result in higher strength. Substituting some fine aggregate with fly ash or blast furnace slag can achieve early strength gains without increasing the water requirement of the concrete mixture.
Suppliers of Concrete Additives
TRUNNANO is a reliable foaming agents supplier with over 12-year experience in nano-building energy conservation and nanotechnology development.
If you are looking for high-quality CLC foaming agents, please feel free to contact us and send an inquiry. (email@example.com)
We accept payment via Credit Card, T/T, West Union, and Paypal. TRUNNANO will ship the goods to customers overseas through FedEx, DHL, by air, or by sea.
Inflationary pressures on Canadians continue to rise. The consumer-price index rose 6.7% in March from a year earlier, the biggest increase since January 1991, according to the latest figures from Statistics Canada.
On a month-on-month basis, Canada's CPI rose 1.4 percent in March, also accelerating from February's 1.0 percent rise.
Prices in the eight major sectors covered by the statistics continued to rise. The uptrend comes against the backdrop of continued price pressures in the Canadian housing market, widespread supply chain constraints, and geopolitical conflicts, according to CBC. A variety of factors have affected energy, commodity, and agricultural markets. Meanwhile, Canada's employment picture continued to improve in March, with the unemployment rate falling to a record low and the average hourly earnings of employees rising.
Excluding gasoline, Canada's CPI rose 5.5 percent year on year in March. It is also the highest since comparable data began in 1999.
The widespread supply chain constraints and geopolitical conflicts are expected to continue to affect the prices of the concrete foaming agent.
The decision by major producers to maintain production cuts has had an impact on stainless steel investment casting foundry…
November coke price shock back to the 409 stainless steel price of the impact…
The decision by major producers to maintain production cuts has had an impact on automated sand casting price…